NOTE ** This section is based on the Islander series of shutter and door products manufactured by Willard Shutter Company, Inc., at the following address:
NOTE ** 4420 N.W. 35th Ct.
NOTE ** Miami FL 33142
NOTE ** Telephone 1-800-826-4530
NOTE ** FAX 1-305-638-8634
NOTE **
NOTE ** Willard Shutter Company, Inc. offers a complete line of products for opening security and sun control.
NOTE **
NOTE ** SECTION 10710 - EXTERIOR SHUTTERS, Copyright 1996, The Architect's Catalog, Inc.
PART 1 GENERAL
1.1 SECTION INCLUDES
NOTE ** Delete items below not required for project.
A. Ornamental Fixed Shutters.
B. Top-Hinged Shutters.
C. Folding Shutters.
D. Sliding Shutters.
E. Sliding Louvered Doors.
F. Folding Louvered Doors.
G. Window and Door Inserts.
H. Equipment Screens.
I. Sunscreens.
1.2 RELATED SECTIONS
NOTE ** Delete any sections below not relevant to this project; add others as required.
A. Section 05500 - Metal Fabrications.
B. Section 06100 - Rough Carpentry.
1.3 REFERENCES
A. ASTM B 209/B 209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate.
B. ASTM B 221/B 221M - Standard Specification for Aluminum and Aluminum-Alloy Bars, Rods, Wire, Shapes, and Tubes.
C. FS HH-I-524A - Specification for Expanded Polystyrene Insulation Board.
1.4 SUBMITTALS
A. Submit under provisions of Section 01300.
B. Product Data: Manufacturer's descriptive literature for products specified in this section.
C. Shop Drawings: Indicate shutter sizes, and mounting details for project conditions.
NOTE ** Delete the following paragraph if specifying custom colors.
D. Selection Samples: Two sets, representing manufacturer's full range of available finish selections.
NOTE ** Delete the following paragraph if specifying standard colors and color matching is not a critical requirement.
E. Verification Samples: Two samples, minimum surface 36 square inches each, indicating match to specified finish.
F. Quality Assurance Submittals:
NOTE ** Delete the following paragraph if specifying No Substitutions in MANUFACTURERS Article.
1. Certificates: Contractor's certification that:
a. Products of this section, as provided, meet or exceed specified requirements.
b. Manufacturer of products of this section meets specified qualifications.
2. Manufacturer's Instructions: Printed installation instructions for each specified product.
G. Closeout Submittals:
1. Operation and maintenance data: Manufacturer's printed instructions for maintaining operating hardware and finishes.
2. Warranty documents: Issued and executed by manufacturer of product, in Owner's name.
1.5 QUALITY ASSURANCE
A. Manufacturer Qualifications: Minimum five (5) years documented experience producing products specified in this section.
B. Regulatory Requirements: Specified products to conform to requirements of South Florida Building Code.
NOTE ** Retain paragraph below if required for extensive or custom installations.
C. Pre-installation Meetings:
1. Convene at job site seven (7) calendar days prior to scheduled beginning of construction activities of this section to review requirements of this section.
2. Require attendance by representatives of the following:
a. Product manufacturer, if requested by installer of this section.
b. Installer of this section.
c. Other entities directly affecting, or affected by, construction activities of this section.
3. Notify Architect four (4) calendar days in advance of scheduled meeting date.
1.6 DELIVERY, STORAGE, AND HANDLING
A. Storage and Protection:
1. Store products of this section in manufacturer's unopened packaging until installation.
2. Maintain dry, heated storage area for products of this section until installation of products.
NOTE ** Retain the following Article for fitting units to existing structures.
1.7 PROJECT/SITE CONDITIONS
A. Existing Conditions: Obtain field measurements of existing openings and verify shop drawing dimensions before fabricating units.
1.8 WARRANTY
A. Manufacturer's Warranty: Supply manufacturer's standard warranty against defects in product workmanship and materials.
NOTE ** Delete one of the two following paragraphs; coordinate with Division 01 requirements.
B. Requests for substitutions will be considered in accordance with provisions of Section 01600.
C. Substitutions: Not permitted.
2.2 MATERIALS
A. Aluminum Sheet: Conforming to ASTM B 209.
B. Aluminum Extrusions and Shapes: Conforming to ASTM B 221.
C. Expanded Polystyrene: Conforming to FS HH-I-524A.
2.3 COMPONENTS
NOTE ** Retain one of the following two paragraphs. If more than one product or finish is required, duplicate entire paragraph and edit for each type. Coordinate Types with drawings if more than one product or finish is required, or if size is specified below. Delete Type designation if only one type is specified.
A. Shutter Unit Type __:
B. Door Unit Type __:
NOTE ** Retain one of the following seven paragraphs.
4. Acceptable Product: Islander Standard Rolling Shutter.
5. Acceptable Product: Islander Sill Track Rolling Shutter.
6. Acceptable Product: Islander Sliding Door.
7. Acceptable Product: Islander Folding Door.
NOTE ** Retain the following paragraph for all products.
8. Product Description: Fixed horizontal-louver shutter, with louver spacing 1-1/4 inches OC vertical, set into foam- filled frame at 44 degrees from horizontal.
a. Frame: Aluminum sheet, Alloy 3004-H36, 0.025 inch minimum sheet thickness; roll-formed to box beam profile 2-1/2 inches wide by 1-5/8 inches deep.
NOTE ** Retain for shutter unit width greater than 26 inches.
b. Intermediate Mullion: Aluminum sheet, Alloy 3004-H36, 0.025 inch minimum sheet thickness; roll-formed to box beam profile 2-1/2 inches wide by 1-5/8 inches deep.
c. Louver: Aluminum sheet, Alloy 3004-H36, 0.025 inch minimum sheet thickness; roll-formed to profile 1-3/4 inches wide, with converse bevelled front and rear edges.
d. Foam Core Material: Expanded polystyrene conforming to FS HH-I-524A.
e. Fasteners: Stainless steel self-tapping machine screws, or aluminum Alloy 2024-T4 pop-rivets, manufacturer's option.
NOTE ** Retain following paragraph if required for added strength of shutter unit.
f. Internal Reinforcement: Aluminum extrusion, Alloy 6063-T5, 0.062 inch minimum wall thickness, mill finish; formed to I-beam profile to fit inside frame.
g. Mounting Hardware: Factory-prepare units for specified mounting hardware.
NOTE ** Determine method of finish selection; coordinate with SUBMITTALS Article. Retain one of the following three paragraphs. Specify custom finish requirements if third paragraph is retained.
9. Finish: Roller-coated baked enamel, medium gloss finish, __________ color.
10. Finish: Roller-coated baked enamel, medium gloss finish, color selected from manufacturer's full range of available colors.
11. Finish: Custom finish, __________.
NOTE ** Retain one of the following two paragraphs. Insert size requirements if second paragraph is retained.
NOTE ** Retain the following paragraph if specifying Islander Decorator Shutter. Delete Shutter Type designation if only one type is specified.
C. Mounting Hardware for Shutter Type __: Anchoring devices; types and sizes specified in shutter manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Colonial Hinged Shutter. Delete Shutter Type designation if only one type is specified.
D. Mounting Hardware for Shutter Type __:
1. Shutter manufacturer's standard mounting hardware as follows:
a. Side Hinges: Aluminum, AAMA anodized finish R1-201; continuous piano hinge.
b. Locking Bar: Aluminum extrusion, Alloy 6063-T5, AAMA anodized finish R1-201.
c. Hold-Open: Friction catch, nickel-plated brass.
2. Anchoring Devices: Types and sizes specified in shutter manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Bahama Shutter. Delete Shutter Type designation if only one type is specified.
E. Mounting Hardware for Shutter Type __:
1. Shutter manufacturer's standard mounting hardware as follows:
a. Header Hinge: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; shutter-mounted pivot and wall-mounted receiver, continuous full shutter width.
NOTE ** Retain one of the following two paragraphs.
b. Adjustable Tube Support: Aluminum extrusions, Alloy 6063-T6; telescoping operation for adjustable shutter projection, maximum 44 degrees from vertical.
c. Fixed Support Components:
NOTE ** Insert shutter projection requirement in the following paragraph.
1) Support Arm: Aluminum extrusion, Alloy 6063-T6; fixed length for shutter projection __ degrees from vertical.
2) Wall Bracket: Aluminum extrusion, Alloy 6063-T6; camel-back bracket pivot-connected to support arm for horizontal or vertical mounting.
NOTE ** Retain one of the following two paragraphs.
3) Shutter Bracket: Aluminum extrusion, Alloy 6063-T6; non-removable pivot connection to shutter for fixed shutter position.
4) Shutter Bracket: Aluminum extrusion, Alloy 6063-T6; removable pivot connection to shutter to allow return of shutter to vertical position.
2. Anchoring Devices: Types and sizes specified in shutter manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Standard Rolling Shutter. Delete Shutter Type designation if only one type is specified.
F. Mounting Hardware for Shutter Type __:
1. Shutter manufacturer's standard mounting hardware as follows:
NOTE ** Retain one of the following two paragraphs.
a. Single Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted rail, continuous full indicated length.
b. Double Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted rail, continuous full indicated length.
c. Roller Bracket: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; shutter-mounted, with nylon roller.
d. Tie-Down Bracket: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; shutter-mounted, with locking device.
2. Anchoring Devices: Types and sizes specified in shutter manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Sill Track Rolling Shutter. Delete Shutter Type designation if only one type is specified.
G. Mounting Hardware for Shutter Type __:
1. Shutter manufacturer's standard mounting hardware as follows:
NOTE ** Retain one of the following two paragraphs.
a. Single Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted rail, continuous full indicated length.
b. Double Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted rail, continuous full indicated length.
c. Roller Bracket: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; shutter-mounted, with nylon roller.
NOTE ** Retain one of the following two paragraphs.
d. Single Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted track, continuous full indicated length.
e. Double Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted track, continuous full indicated length.
f. Guide Stud: Aluminum extrusion, Alloy 6063-T6, vinyl-coated; shutter-mounted for aligning bottom of shutter with sill track.
g. Locking Device: Flush bolt mounted at bottom of shutter.
2. Anchoring Devices: Types and sizes specified in shutter manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Sliding Door. Delete Door Type designation if only one type is specified.
H. Mounting Hardware for Door Type __:
1. Door manufacturer's standard mounting hardware as follows:
NOTE ** Retain one of the following two paragraphs.
a. Single Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted rail, continuous full indicated length.
b. Double Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted rail, continuous full indicated length.
c. Roller Bracket: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; door-mounted, with nylon roller.
NOTE ** Retain one of the following two paragraphs.
d. Single Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted track, continuous full indicated length.
e. Double Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted track, continuous full indicated length.
f. Guide Stud: Aluminum extrusion, Alloy 6063-T6, vinyl-coated; door-mounted for aligning bottom of door with sill track.
g. Locking Device: Flush bolt mounted at bottom of door.
2. Anchoring Devices: Types and sizes specified in door manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph if specifying Islander Folding Door. Delete Door Type designation if only one type is specified.
I. Mounting Hardware for Door Type __:
1. Door manufacturer's standard mounting hardware as follows:
a. Side Hinges: Aluminum, AAMA anodized finish R1-201; continuous piano hinge.
NOTE ** Retain one of the following two paragraphs.
b. Single Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted rail, continuous full indicated length.
c. Double Head Rail: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted rail, continuous full indicated length.
d. Roller Bracket: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; door-mounted, with nylon roller.
NOTE ** Retain one of the following two paragraphs.
e. Single Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; single wall-mounted track, continuous full indicated length.
f. Double Sill Track: Aluminum extrusion, Alloy 6063-T6, AAMA anodized finish R1-201; double wall-mounted track, continuous full indicated length.
g. Guide Stud: Aluminum extrusion, Alloy 6063-T6, vinyl-coated; door-mounted for aligning bottom of door with sill track.
h. Locking Device: Flush bolt mounted at bottom of door.
2. Anchoring Devices: Types and sizes specified in door manufacturer's printed instructions for project conditions.
NOTE ** Retain the following paragraph for non-standard shutter or sunscreen installations, or equipment screen.
J. Support Structure: Specified in Section 05500.
PART 3 EXECUTION
3.1 EXAMINATION
A. Verification of Conditions:
1. Openings are correct sizes in accordance with Architect-accepted shop drawings.
2. Substrates are prepared to receive products of this section.
B. Installer's Examination:
1. Have installer of this section examine conditions under which construction activities of this section are to be performed, then submit written notification if such conditions are unacceptable.
2. Transmit two copies of installer's report to Architect within 24 hr. of receipt.
3. Beginning construction activities of this section before unacceptable conditions have been corrected is prohibited.
4. Beginning construction activities of this section indicates installer's acceptance of conditions.
3.2 INSTALLATION
A. Install products specified in this section in accordance with Architect-approved shop drawings and manufacturer's printed installation instructions.
NOTE ** Delete the following Article if specifying Ornamental Fixed Shutters only.
3.3 ADJUSTING
A. Adjust operating hardware for correct operation of units in accordance with manufacturer's printed instructions.
3.4 CLEANING
A. Clean finishes of units in accordance with manufacturer's printed instructions.
3.5 PROTECTION OF INSTALLED PRODUCTS
A. Protect units from damage by subsequent construction activities until Substantial Completion; replace damaged units having damage other than minor finish damage at Contractor's expense.
B. Repair minor finish damage to units in accordance with manufacturer's instructions; Architect will be sole judge of acceptability of repairs.
